Intralox

Intralox Engineering Manual (pdf)

Thermodrive Engineering Manual 2018 (pdf)

S4009 Flat Top Chain

The 83.8 mm chain width conforms to European conveyor design standards. Same top thickness as Series 900 Flat Top [0.384” (9.8 mm)]. Available in boxed lengths of 10′ (3.05 m).

S4009 Flush Grid Chain

83.8 mm chain with 13% open area. Same top thickness as Series 900 Flush Grid [0.344” (8.7 mm)]. Available in boxed lengths of 10′ (3.05 m).

S4014 Flat Top Chain

83.8 mm chain with same top thickness as Series 1400 Flat Top [0.5” (12.7 mm)] for heavy-duty applications. Available in boxed lengths of 10′ (3.05 m).

Accessories

Sprockets

Series 4000 Sideflexing Chains utilize Series 1400 sprockets. Square bore sprockets are available in 12 tooth, 3.9″ (99 mm); 16 tooth, 5.1″ (130 mm); 18T, 5.7″ (145 mm), shown and 21T, 6.7″ (170 mm) nom. pitch diameters. Beveled hold down eliminates need for expensive magnetic corner track. Crescent-shaped modules and one-inch pitch minimize gaps through turns.

Knuckle Chain

Offers a thick, durable plastic surface around stainless steel pins for long life and less breakage. Center driven nominal 2” pitch (50.8 mm). The Series 3000 Knuckle Chain comes in both straight and turning versions. Turning version strength is 560 lb/ft (254 kg/m). Available in boxed lengths of 10′ (3.05 m).

Accessories

Sprockets

Square and round bore sprockets are available in 8 tooth, 5.2″ (132 mm); 10T, 6.5″ (165 mm) and 12T, 7.7″ (196 mm, shown), nom. pitch diameters.

Extended Pins

Modules with 303 stainless steel extended pins for use in turning and straight running chains. These pins are commonly used in side by side chain strands when rollers are used for low back pressure applications.

Extended Tabs

Modules with extended tabs for use in turning and straight running chains. These extended tabs can be used to attach flights, cleats, etc.

Radius

Strong, versatile belt with small holes, 42% open area and a 2.2 turning radius. Durable and easy to clean. Small pitch allows tight transfers for delicate products.

Tight Turning Radius

Same interior design as series 2400 Radius (2.2 turning version), but with edge modules that collapse tighter, allowing for down to a 1.7 turning radius up to 24” wide (18” wide in spiral applications). Contact customer service for specific conveyor requirements.

Radius Friction Top

Friction top modules can be built into either turning radius version. Rubber is bonded to the top surface of interior modules and provides a friction top surface for inclines and declines.

Tight Turning Radius with Roller Inserts

Designed for low back pressure accumulation in applications requiring a radius belt. Offers 42% open area and a 1.7 turning radius up to 24” wide (18” wide in spiral applications). Wide roller-to-rod contact area means less wear.

Radius with Roller Inserts

Designed for low back pressure accumulation in applications requiring a radius belt. Offers 42% open area and a 2.9 turning radius. Wide roller-to-rod contact area means less wear. NOTE: belt strengths are for 3” roller width spacing.

Accessories

Molded Sprockets

Molded sprockets are available in the following nom. pitch diameters: 6 tooth, 2.0″ (51 mm); 9T, 2.9″ (74 mm); 12T, 3.9″ (99 mm); 16T, 5.1″ (130 mm) and 20T, 6.4″ (163 mm). Round bore sizes also available.

Flights

Intralox 3” (76 mm) No-Cling Flights for Series 2400. The flight’s “ridges” are part of the No-Cling design which reduces product sticking to improve yield.

Hold Down Guide

Guide is on the bottom of the belt for use when the belt edges need to be clear. The hold down guide steers the belt through the turns and holds it in place vertically.

Sideguards

Universal and Clip-On Sideguards assure product containment in high speed and general spiral applications and incline/decline applications. The Universal Sideguard is available in 1” (25 mm) and 3” (76 mm), and is an integral part of the belt, fastened by hinge rods. The Clip-On Sideguard snaps into the belt’s edge modules with 2.2 turn ratio and is available in 0.75” (19 mm).

Flush Grid Radius

Strong, versatile belt with 50% open area and 2.2 turn radius. USDA accepted. Available with or without tabbed edge for hold down. Flights are available for incline applications. Headless rod retention system allows re-use of rods.

Radius Friction Top

The rubber friction surface is now co-molded to the top of the belt. Offers increased rubber grip surface area, which provides greater durability and longer belt life. Available with or without tabbed edge for hold down. Headless rod retention system allows re-use of rods.

Accessories

Molded Sprockets

Molded sprockets are available in the following nominal pitch diameters: 8 tooth, 3.9″ (99 mm); 11T, 5.3″ (135); 13T, 6.3″ (160 mm), shown; and 16T, 7.7″ (196 mm).

Flights

Streamline Flights are available 4” (102 mm) high and can be cut down to any height. No fasteners are required. Flights can be provided in linear increments of 1.5” (38 mm). The standard indent is 5/8”.

Flat Top

New, highly impact-resistant belt developed for tough meat applications. The 2.5” (63.5 mm) belt pitch plus the 1” transverse pitch (distance between hinges) has 50% fewer pockets to trap debris. Headless rod retention design allows less chance for breakage and easier maintenance and repair.

Mesh Top

Slots are larger and are tapered, providing optimum water flow for drainage and product dewatering. Unique slot size prevents small to medium-sized product or stems from being pulled out or lost in production. 32% open area and open hinges promote fast, thorough clean up.

Accessories

Sprockets

Molded EZ Clean sprockets are available in 6 tooth, 5.0” (127 mm), 8T, 6.5” (165 mm), 10T, 8.1” (206 mm) and 13T, 10.5” (267 mm) pitch diameters.

Flight

4” (106 mm) molded impact resistant flights are available, and may be cut down to other heights to meet customer requirements.

Open Hinge Flat Top

Cam-link designed hinges allow the belt to open up more around the sprocket for easier access to hinge area for cleaning. Sculpted, radiused underside and large corner rounds prevent debris build up, making cleaning easier and faster.

Accessories

Sprockets

Sprockets are available in the following nom. pitch diameters: 6 tooth, 2.0″ (51 mm) 10T, 3.2″ (82 mm), 12T, 3.9″ (98 mm), and 20T, 6.4″ (162 mm).

No-Cling Flights

Intralox 4” (102 mm) No-Cling Flights for Series 1600. The flight’s “ridges” are part of the No-Cling design which reduces product sticking and improves yield.