Intralox Series 900
Low profile transverse ridges are 0.188″ (4.78 mm) high for moving products up inclines. 38% open area. USDA accepted for raw meat or poultry. Recessed snap-in rods and fully flush edges.
Strong 1″ (27 mm) nom. pitch belt. Features fully flush edges and snapin rods. 38% open area. USDA accepted for raw meat or poultry. Also available in ONEPIECE™ Live Transfer style.
Thick surface for long service life. Top is beveled at edge for side transfers. Small, 1” (27 mm) nom. pitch facilitates smooth operation with minimal chordal action, dead plate gap and speed pulsation. Also available in ONEPIECE™ Live Transfer style.
Strong 1″ (27 mm) nom. pitch belt. Features fully flush edges and snapin rods. 38% open area. USDA accepted for raw meat or poultry.
Perforated Flat Top
Thick surface for long service life. Available in 1/8” (3.2 mm), 5/32” (4 mm) and 3/16” (4.8 mm) hole sizes. Designed for vacuum transfer applications with scalloped underside to reduce carryway blockage.
Diamond Friction Top (DFT) and DFT Ultra
Two-material modules provide a high friction surface without interfering with carryways and sprockets for incline and decline applications. White materials comply with FDA regulations.
Flat Friction Top (FFT) and FFT Ultra
The same design principles and advantages as Series 900 Diamond Friction Top, with a flat surface of high friction rubber. White materials comply with FDA regulations.
Open hinge design for improved sanitation. 24% open area allows fast, efficient drainage, eliminating tendency of water to rest on the belt’s surface. Small holes prevent stems from getting caught. 1” (27 mm) nom. pitch allows for tight transfers.
Square Friction Top (SFT)
Two-material modules provide a high friction surface without interfering with carryways and sprockets for incline and decline applications. Comes in SFT and SFT Ultra (higher rubber concentration). Available with flat top or flush grid edge modules.
Flush Grid and Flat Top Mold To Width Chain
Series 900 Flush Grid and Flat Top are available in industry standard widths – 3.25” (83 mm), 4.5” (114 mm) and 7.5” (191 mm). Also available in 85 mm widths for international markets. Call Intralox or refer to the Intralox Engineering Manualfor specific belt strengths.
Raised Rib Mold To Width Chain
Series 900 Raised Rib is available in 1.1” (29 mm), 1.5” (37 mm), 1.8” (46.5 mm) and 2.2” (55 mm). All chains come with nylon rodlets standard, providing longer service life. Call Intralox or refer to the Intralox Engineering Manual for specific belt strengths.
Molded and Split Sprockets
Intralox offers molded sprockets with 6, 9, 10, 12, 17, 18 or 20 teeth. Split sprockets are available with 12, 15, 17, 18, 20 or 28 teeth. Intralox can manufacture sprockets (both plastic and split) with different numbers of teeth if the application cannot use the standard sizes.
Molded Toothplate Split Sprocket
These new sprockets provide flexibility for easier retrofits and change-outs. They are available in 6.1” (155 mm) and 6.8” (173 mm) sizes. Sprocket hub is polypropylene, with glass-filled nylon toothplate.
Flush Grid base flights are available in 1” (25 mm) and 2” (51 mm) heights. Flat Top base flights are available in 1” (25 mm), 2” (51 mm) and 3” (76 mm) heights. These flights can be cut down to any height to meet customer requirements.
Sideguards are used to assure product containment and are available 2” (51 mm) high. Made in the standard overlapping design, they are an integral part of the belt and are fastened by the hinge rods.
Finger Transfer Plates
These comb-like plates are designed to eliminate tipping problems at product transfer. The 18 fingers extend between the belt’s ribs, allowing a smooth continuation of product flow. Available in 4” (102 mm) 12 finger for use when retrofitting from Series 100 Raised Rib.