TM400 Specifications

Drum Motor & Idler Dimensions
Bracket Dimensions
Optional Cable Type Dimensions
Drum Motor Specifications
Cross Sectional Diagram
Parts Description

Dimensions (in inches)

Drum Motor
TM400A60

Drum Motor
TM400B60

Idler
KT400A60

Idler
KT400B60

Standard face widths (L) in inches for the TM400A60 and KT400A60: 23.62*   25.59*   27.56   29.53   31.50   33.46   35.43   37.40   39.38   41.34   43.31   45.28

Standard face widths (L) in inches for the TM400B60 and KT400B60: 25.59*   27.56*   29.53   31.50   33.46   35.43   37.40   39.38   41.34   43.31   45.28 

*This face width is not available in all horsepower.

back to top

Bracket AB 60

Optional Cable Type

Note: When Optional Cable Type is selected, the minimum face width (L) increased by 3.94 inches.

back to top

Specifications

Type	HP	Belt speed in feet per minute (ft/min) Belt pull measured in pounds (lbs.)														Minimum length (L) in inches		Weight in pounds (lbs.) at L = 25.59 inches
																Design A	Design B
TM400 - 420	20.0	869	628	579	524	491	413	380	347	300	250	*210	*182	*151	(ft/min)	27.56	29.53	539.40
		759	1050	1130	1251	1343	1680	1729	2000	2315	2774	3302	3810	4593	(belt pull)
TM400 - 415	15.0	869	628	579	524	491	413	380	347	300	250	*210	*182	*151	(ft/min)	25.59	29.53	534.60
		533	737	850	932	987	1120	1288	1333	1543	1849	2201	2540	3061	(belt pull)
TM400 - 410	10.0	869	628	579	524	491	413	380	347	300	250	210	182	151	(ft/min)	23.62	25.59	507.10
		355	491	555	589	665	774	812	939	1037	1244	1468	1697	2042	(belt pull)
TM400 - 475	7.5	524	380	298	224	210	182	151	(ft/min)							23.62	25.59	496.00
		441	609	778	1032	1101	1273	1531	(belt pull)
TM400 - 675	7.5	345	248	196	146	137	118	99	(ft/min)							23.62	25.59	496.00
		671	933	1181	1580	1690	1960	2333	(belt pull)
TM400 - 455	5.5	524	380	298	224	210	182	151	(ft/min)							23.62	25.59	485.00
		324	446	570	756	807	933	1123	(belt pull)
TM400 - 655	5.5	345	248	196	146	137	118	99	(ft/min)							23.62	25.59	485.00
		448	623	788	1054	1126	1306	1555	(belt pull)
TM400 - 44	4.0	524	380	298	224	210	182	151	(ft/min)							23.62	25.59	474.00
		235	325	415	550	587	679	817	(belt pull)
TM400 - 84	4.0	253	182	144	109	102	87	73	(ft/min)							23.62	25.59	496.00
		488	679	857	1136	1215	1413	1686	(belt pull)
TM400 - 83	3.0	253	182	144	109	102	87	73	(ft/min)							23.62	25.59	485.00
		366	509	643	852	912	1059	1264	(belt pull)
TM400 - 123	3.0	163	118	92	69	66	57	47	(ft/min)							23.62	25.59	507.10
		568	784	1005	1352	1400	1633	1960	(belt pull)
* Please consult the Van der Graaf technical department for use of these speeds. - Other belt speeds and face widths are available. - The total weight of the unit increases by 6.72 pounds per inch above 25.59 inches. - When the drive is supplied with lagging, the covered face width is reduced by 1.42 inches. - Belt speed is measured on the center of the unit without lagging. - Listed belt speeds are under full load conditions and may be higher under no load conditions. - When an electromagnetic brake is required, the minimun face width is increased by 5.91 inches. NOTE: TM400 type drum motors are available in all standard voltages and are electrically reversible.

back to top

Cross Sectional Diagram & Parts Description

 

Position Number	Part Description	Position Number	Part Description
1	Shell	33	Socket Head Cap Screw
2A	End Flange	34	Filler Plug
2B	End Flange	35	Washer
3	Gear Housing	36	Ball Bearing
4	Motor Flange	36V	Cylindrical Bearing
6	Shaft End	37	Ball Bearing
7	Hollow Shaft	38	Ball Bearing
8	External Gear	39	Needle Bearing
9/10	Pinion with Bushing	40	Shim
11	Gear	41	Locking Disc
12	Distance Ring	42	Snap Ring
13	Stator	43	Snap Ring
14	Rotor	44	Snap Ring
15	Socket Head Cap Screw	45A	Bearing Race
16	Cable Passage	45B	Bearing Race
18	Gasket	45DS	Double Seal Adaptor
20	Terminal Board	46	Oil Seal
23	Fillister Head Machine Screw	50	Seal
24	Fillister Head Machine Screw	51	Junction Box
27	Set Screw	52	Junction Box Cover
28	Set Screw	53	Plug
29	Key	54	Key
31	Socket Head Cap Screw	55	Backstop Bearing
32	Washer Copper	57	Name Plate

back to top