TM113 Specifications

Drum Motor & Idler Dimensions
Bracket Dimensions
Optional Cable Type Dimensions
Drum Motor Specifications
Cross Sectional Diagram
Parts Description

Dimensions (in inches)

Drum Motor
TM113B25

Idler
KT113B25

Standard face widths (L) in inches for the TM113B25 and KT113B25: 10.24*   10.83*   12.20   14.17   16.14   18.11   20.08   22.05   24.02   25.98   27.95   29.92   31.89   33.86

Slow Speed: 12.20*   14.17*   16.14   18.11   20.08   22.05   24.02   25.98   27.95   29.92   31.89   33.86 

*This face width is not available in all horsepower.

back to top

Bracket AB 20

Optional Cable Type

Note: When Optional Cable Type is selected, the minimum face width (L) increased by 1.969 inches.

back to top

Specifications

Type	HP	Belt speed in feet per minute (ft/min) Belt pull measured in pounds (lbs.)														Minimum length (L) in inches Design B	Weight in pounds (lbs.) at L = 10.24 inches
TM113 - 434	0.34	522	468	373	333	295	260	227	203	179	170	151	127	120	(ft/min)	12.20	34.10
		19	21	27	28	34	38	44	49	55	59	66	78	82	(belt pull)
		106	94	80	64	(ft/min)
		94	105	124	156	(belt pull)
TM113 - 625	0.25	331	298	236	210	187	165	144	113	95	80	69	59	50	(ft/min)	12.20	34.10
		22	24	30	34	38	43	50	63	76	89	105	121	144	(belt pull)
		40													(ft/min)
		178													(belt pull)
TM113 - 425	0.25	373	333	295	260	227	203	179	170	151	127	120	106	94	(ft/min)	10.83	34.10
		19	22	24	27	32	35	40	42	47	56	59	67	76	(belt pull)
		80	64	(ft/min)
		89	112	(belt pull)
TM113 - 816	0.16	73	61	52	47	38	31								(ft/min)	12.20	34.10
		65	78	92	101	126	155								(belt pull)
TM113 - 416	0.16	260	227	203	179	170	151	127	120	106	94	80	64	(ft/min)		10.24	34.10
		18	21	24	27	28	32	37	40	45	50	59	75	(belt pull)
TM113 - 811	0.11	73	61	52	47	38	31								(ft/min)	10.24	34.10
		43	52	61	67	84	104								(belt pull)
SLOW SPEED
TM113 - 434PL2	0.34	54	48	45	40	34	32	28	27	25	21	17	(ft/min)			14.17	37.10
		212	239	251	274	274	274	274	274	274	274	274	(belt pull)
TM113 - 434PL3	0.34	13.2	11.7	9.9	8.3	7.9	6.9	6.2	5.2	4.2					(ft/min)	16.14	40.10
		274	274	274	274	274	274	274	274	274					(belt pull)
TM113 - 625PL2	0.25	35	31	30	26	22	21	19	18	16	14	11	(ft/min)			14.17	37.10
		237	267	274	274	274	274	274	274	274	274	274	(belt pull)
TM113 - 625PL3	0.25	8.7	7.7	6.5	5.4	5.2	4.5	4.0	3.4	2.7					(ft/min)	16.14	40.10
		274	274	274	274	274	274	274	274	274					(belt pull)
TM113 - 425PL2	0.25	54	48	45	40	34	32	28	27	25	21	17	(ft/min)			12.80	37.10
		156	175	185	208	249	259	274	274	274	274	274	(belt pull)
TM113 - 425PL3	0.25	13.2	11.7	9.9	8.3	7.9	6.9	6.2	5.2	4.2					(ft/min)	14.76	40.10
		274	274	274	274	274	274	274	274	274					(belt pull)
TM113 - 816PL2	0.16	26	23	22	19	16	13	12	10	8	(ft/min)					12.20	37.10
		205	231	243	274	274	274	274	274	274	(belt pull)
TM113 - 816PL3	0.16	6.4	5.7	4.8	4.0	3.8	3.4	3.0	2.5	2.0					(ft/min)	14.17	40.10
		274	274	274	274	274	274	274	274	274					(belt pull)
TM113 - 416PL2	0.16	54	48	45	40	34	32	28	27	25	21	17	(ft/min)			12.20	37.10
		100	112	118	133	159	166	189	197	213	255	274	(belt pull)
TM113 - 416PL3	0.16	13.2	11.7	9.9	8.3	7.9	6.9	6.2	5.2	4.2					(ft/min)	14.17	40.10
		274	274	274	274	274	274	274	274	274					(belt pull)
TM113 - 811PL2	0.11	26	23	22	19	16	13	12	10	8	(ft/min)					14.17	37.10
		141	159	167	189	225	268	274	274	274	(belt pull)
TM113 - 811PL3	0.11	6.4	5.7	4.8	4.0	3.8	3.4	3.0	2.5	2.0					(ft/min)	16.14	40.10
		274	274	274	274	274	274	274	274	274					(belt pull)
- Other belt speeds and face widths are available. - The total weight of the unit increases by 1.0 pounds per inch above 10.24 inches. - When the drive is supplied with lagging, the covered face width is reduced by 0.47 inches. - Belt speed is measured on the center of the unit without lagging. - Listed belt speeds are under full load conditions and may be higher under no load conditions. NOTE: TM113 type drum motors are available in all standard voltages and are electrically reversible.

back to top

Cross Sectional Diagram & Parts Description

Position Number	Part Description	Position Number	Part Description
1	Shell	22	O-Ring
2A	End Flange	23	Fillister Head Machine Screw
2B	End Flange	24	Fillister Head Machine Screw
3	Gear Housing	27	Set Screw
4	Motor Flange	31	Socket Head Cap Screw
4A	Motor Flange	32	Washer Copper
5	Mounting Ring	36	Ball Bearing
5A	Mounting Ring	37	Ball Bearing
6	Shaft End	37A	Ball Bearing
7	Hollow Shaft	38	Ball Bearing
8	Internal Gear	39	Needle Bearing
9	Pinion	44	Snap Ring
11	Gear	45	Bearing Race
13	Stator	45C	Shim Plate
14	Rotor	45D	Gamma Ring
14A	Insert pinion	46	Oil Seal
15	Socket Head Cap Screw	49	Wave Washer
15A	Socket Head Cap Screw	50	Seal
16	Cable Passage	51	Junction Box
17	Socket Head Cap Screw	52	Junction Box Cover
19	Spring Ring	53	Plug
20	Terminal Board	55	Backstop Bearing
21	Spring Ring	57	Name Plate

back to top