Open Grid
Low profile transverse ridges are 0.188" (4.78 mm) high for moving
products up inclines. 38% open area. USDA accepted for raw meat or
poultry. Recessed snap-in rods and fully flush edges.
|
Flush Grid
Strong 1" (27 mm) nom. pitch belt. Features fully flush edges and
snapin rods. 38% open area. USDA accepted for raw meat or poultry.
Also available in ONEPIECE™ Live Transfer style.
|
Flat Top
Thick surface for long service life. Top is beveled at edge
for side transfers. Small, 1” (27 mm) nom.
pitch facilitates smooth operation with minimal chordal action, dead plate
gap and speed pulsation. Also available in ONEPIECE™ Live Transfer style.
|
|
|
|
|
|
Raised Rib
Strong 1" (27 mm) nom. pitch belt. Features fully flush edges and
snapin rods. 38% open area. USDA accepted for raw meat or
poultry.
|
Perforated Flat
Top
Thick surface for long service life. Available in
1/8'' (3.2 mm), 5/32'' (4 mm) and 3/16'' (4.8 mm) hole sizes.
Designed for vacuum transfer applications with scalloped underside
to reduce carryway blockage.
|
Diamond Friction
Top (DFT) and DFT Ultra
Two-material modules provide a
high friction surface without interfering with carryways and
sprockets for incline and decline applications. White materials
comply with FDA regulations.
|
|
|
|
|
|
Flat Friction Top
(FFT) and FFT Ultra
The same design principles and
advantages as Series 900 Diamond Friction Top, with a flat surface
of high friction rubber. White materials comply with FDA
regulations.
|
Mesh
Top
Open hinge design for improved sanitation. 24% open
area allows fast, efficient drainage, eliminating tendency of
water to rest on the belt’s surface. Small holes prevent stems
from getting caught. 1'' (27 mm) nom. pitch allows for tight
transfers.
|
Square Friction Top
(SFT)
Two-material modules provide a high friction
surface without interfering with carryways and sprockets for
incline and decline applications. Comes in SFT and SFT Ultra
(higher rubber concentration). Available with flat top or flush
grid edge modules.
|
|
|
|
|
|
Flush Grid and Flat
Top Mold To Width Chain
Series 900 Flush Grid and Flat
Top are available in industry standard widths – 3.25'' (83 mm),
4.5'' (114 mm) and 7.5'' (191 mm). Also available in 85 mm widths
for international markets. Call Intralox or refer to the Intralox
Engineering Manualfor specific belt strengths.
|
Raised Rib Mold To
Width Chain
Series 900 Raised Rib is available in 1.1''
(29 mm), 1.5'' (37 mm), 1.8'' (46.5 mm) and 2.2'' (55 mm). All
chains come with nylon rodlets standard, providing longer service
life. Call Intralox or refer to the Intralox Engineering Manual
for specific belt strengths.
|
|
|
|
|
|
| Accessories
|
|
|
Molded and Split
Sprockets
Intralox offers molded sprockets with 6, 9, 10,
12, 17, 18 or 20 teeth. Split sprockets are available with 12, 15,
17, 18, 20 or 28 teeth. Intralox can manufacture sprockets (both
plastic and split) with different numbers of teeth if the
application cannot use the standard sizes. |
 |
Molded Toothplate
Split Sprocket
These new sprockets provide flexibility
for easier retrofits and change-outs. They are available in 6.1''
(155 mm) and 6.8'' (173 mm) sizes. Sprocket hub is polypropylene,
with glass-filled nylon toothplate. |
 |
Flights
Flush Grid base flights are available in 1'' (25 mm) and
2'' (51 mm) heights. Flat Top base flights are available in 1''
(25 mm), 2'' (51 mm) and 3'' (76 mm) heights. These flights can be
cut down to any height to meet customer requirements. |
 |
Sideguards
Sideguards are used to assure product containment and are
available 2'' (51 mm) high. Made in the standard overlapping
design, they are an integral part of the belt and are fastened by
the hinge rods. |
 |
Finger Transfer
Plates
These comb-like plates are designed to eliminate
tipping problems at product transfer. The 18 fingers extend
between the belt’s ribs, allowing a smooth continuation of product
flow. Available in 4'' (102 mm) 12 finger for use when
retrofitting from Series 100 Raised
Rib. |
